Hi all. nissan navara denso 23710 4x03a MB275800-7451 possible immo off? diagnostic no communication to ecu, clima and rdio not working, immo light flashing when key in ignition.
↧
nissan navara immo
↧
Dacia Sandero 1.4 EMS3132 immo off
↧
↧
mileage 93s56
↧
Update discover mib2 pro
Please help me with firmware update mib 2 pro.Thanks.I have firmware MHI2_ER_VWG11_K0259.
↧
BMW F30 LED headlights- coding DRL without low beam
Hi,
How to code daytime running lights in a way that only rings are active? I have this on position “0” on lights switch, but I would like to have it on “auto” position. Do I have to code FLE or FEM and which options? Thanks!
How to code daytime running lights in a way that only rings are active? I have this on position “0” on lights switch, but I would like to have it on “auto” position. Do I have to code FLE or FEM and which options? Thanks!
↧
↧
Hyundai H1 Edc15C7 0281011576 Immo off
↧
Hyundai i10 Immo off
↧
Xentry 2018.09 internal error :(3.2307)- 3.27
Hello mates,
Hope anyone can help me solving my issue.
I have xentry 2018.09 openshell . The software runs perfectly but after some time it gives :
internal error: (3.2307)- 3.27 and closes directly when clicking on ok.
Anyone can help?
Hope anyone can help me solving my issue.
I have xentry 2018.09 openshell . The software runs perfectly but after some time it gives :
internal error: (3.2307)- 3.27 and closes directly when clicking on ok.
Anyone can help?
↧
renault megane seruis32 immo off
I have renault megane seruis32 ecu WITHOUT CAN ... only have 2 ICs in the corner not 3.
i need to make immo off because there is an error in immo system.
i tried by the way of putting FF from address 4000 to 7FFF then remove 33kohm resistor in pin 58 BUT it fails... security light keep flashing and car dont run.
NOTE: i keep the 4D transponder in the key.
i need to make immo off because there is an error in immo system.
i tried by the way of putting FF from address 4000 to 7FFF then remove 33kohm resistor in pin 58 BUT it fails... security light keep flashing and car dont run.
NOTE: i keep the 4D transponder in the key.
renault megane 29f200 flash seruis32 ORIGINAL.zip | ||
File Type: |
![]() |
![]() |
Downloaded: | 0 times | |
Size: | 101 KB |
↧
↧
Hu Service Manager issue
Hi to u all !
I just wanted to ask:
I got yesterday a f48 X1 01/2018 and couldnt write the service list in service history.
The hu service I am using wrote " no identification"
So i am guessing beacause the car is new , and the program I have is a bit old
I am missing something from the prg files ?
The car had the new nbt evo screen id6.
Does hu service manager work on these screens ??
Any help would be appreciated !!
Thanks in advance
I just wanted to ask:
I got yesterday a f48 X1 01/2018 and couldnt write the service list in service history.
The hu service I am using wrote " no identification"
So i am guessing beacause the car is new , and the program I have is a bit old
I am missing something from the prg files ?
The car had the new nbt evo screen id6.
Does hu service manager work on these screens ??
Any help would be appreciated !!
Thanks in advance

↧
2011 VW Golf ABS coding
↧
Need PLA 3.0 Parameter File for 5QA919298H
Purchased a control module 5QA919298H for uprgrading PLA 2.0 to 3.0. Module came virgin/blank and i am unable to code it.
Will need parameterization file frf file for ODIS
Module : 5QA919298H
Version H08, SW Revision 0061
For Vehicle : Mk7 Golf or Skoda.
Any help will be greatly appreciated.
Will need parameterization file frf file for ODIS
Module : 5QA919298H
Version H08, SW Revision 0061
For Vehicle : Mk7 Golf or Skoda.
Any help will be greatly appreciated.
↧
Powersteering flash file
Hello, I want to make flash of the powersteering unit at VW Sharan via ODIS Engineering. It is 5N1909144M and SW is 1002. I know, that I have to use two SGO files to do it and than will be also changed the hw number of the unit. Can anybody advise me please, wich sgo files should I use?
Thank You very much.
Thank You very much.
↧
↧
REMOVE DTC VISTEON DCU104
↧
Audi A5 3.0 240hp
↧
Ford Galaxy 2008 2.0 tdci 140ps SID206 Vmax
Hi to all. I have a car as in the title and I have a question about vmax.
Where is the limiter saved?
Ecu? Instrument Cluster?
Where is the limiter saved?
Ecu? Instrument Cluster?
↧
EGR Off
↧
↧
Mercedes VPN
Help guys! How to set up "teamviewer VPN"? What should be the IP of both computers? I have a connection and see SDconnect but as soon as I try to make a connection with the machine, a connection error occurs immediately!
↧
Vw MED9.5.10 DTC off
↧
CDR23 Becker 6612
is it possible to deactivate the Can bus in this Radio to fix it in a Car without Can bus?
↧