Hi,
Retrofitting Top Rear Side View Camera $3AH to 2010 BMW X5 E70 VIN L293857
Have fitted all the hardware and HSD cables etc and have successfully coded $430 (folding Mirrors).
Started coding $3AH, added $3AH to the FA on CAS and FRM and all the modules I tried coding were OK (Kombi, RDC, IHKA)
However, when I coded the CIC (C1A) I got this error ...
[14:04:46.339] [2019-09-08] [SERIE] 4440 Trace CBD_PROC.C GetCbdFile 9
[14:04:46.339] [2019-09-08] [SERIE] Paramaterschlüsselwort ungültig 003000'01,HIST_GAS_CONSUMP_SCALE_1 (7538d, 1D72h)
[14:04:46.340] [2019-09-08] [SERIE] 1043 Error CDH.C CDHGetNettoDataFromCbd 1
[14:04:46.340] [2019-09-08] [SERIE] Fehler bei CBD-Dateiverarbeitung CIC.C1A
[14:04:46.443] [2019-09-08] [SERIE] 1043 Error COAPI2.CPP coapiRunCabd 6
[14:04:46.443] [2019-09-08] [SERIE] Fehler bei CBD-Dateiverarbeitung SG_CODIEREN
Researching for literally hours revealed that it looks as if there is a parameter error in the coding relating to the HIST_GAS_CONSUMP_SCALE_1 and when I look at that section of the trace file it looks like this ...
HIST_GAS_CONSUMP
nicht_aktiv
HIST_GAS_CONSUMP_SCALE_1
na
HIST_GAS_CONSUMP_SCALE_2
na
HIST_GAS_CONSUMP_SCALE_3
na
HIST_GAS_CONSUMP_SCALE_4
na
I am using NCS Expert with DCAN properly configured (Although it gave me dramas establishing a connection initially until I set the DCAN switch to pre 2007 cars????)
I have the 3.66 Datens copied to all the relevant folders in NCS and EDIABAS and I am at a loss on how to proceed ...
Anyone have any idea?
Is the “na” in the above trace not acceptable?
Should I change this to nicht_aktiv or to anything else?
I am baffled ... what should be simple coding within reason is giving me sleepless nights!
Any Ideas? Thanks in advance ...
Retrofitting Top Rear Side View Camera $3AH to 2010 BMW X5 E70 VIN L293857
Have fitted all the hardware and HSD cables etc and have successfully coded $430 (folding Mirrors).
Started coding $3AH, added $3AH to the FA on CAS and FRM and all the modules I tried coding were OK (Kombi, RDC, IHKA)
However, when I coded the CIC (C1A) I got this error ...
[14:04:46.339] [2019-09-08] [SERIE] 4440 Trace CBD_PROC.C GetCbdFile 9
[14:04:46.339] [2019-09-08] [SERIE] Paramaterschlüsselwort ungültig 003000'01,HIST_GAS_CONSUMP_SCALE_1 (7538d, 1D72h)
[14:04:46.340] [2019-09-08] [SERIE] 1043 Error CDH.C CDHGetNettoDataFromCbd 1
[14:04:46.340] [2019-09-08] [SERIE] Fehler bei CBD-Dateiverarbeitung CIC.C1A
[14:04:46.443] [2019-09-08] [SERIE] 1043 Error COAPI2.CPP coapiRunCabd 6
[14:04:46.443] [2019-09-08] [SERIE] Fehler bei CBD-Dateiverarbeitung SG_CODIEREN
Researching for literally hours revealed that it looks as if there is a parameter error in the coding relating to the HIST_GAS_CONSUMP_SCALE_1 and when I look at that section of the trace file it looks like this ...
HIST_GAS_CONSUMP
nicht_aktiv
HIST_GAS_CONSUMP_SCALE_1
na
HIST_GAS_CONSUMP_SCALE_2
na
HIST_GAS_CONSUMP_SCALE_3
na
HIST_GAS_CONSUMP_SCALE_4
na
I am using NCS Expert with DCAN properly configured (Although it gave me dramas establishing a connection initially until I set the DCAN switch to pre 2007 cars????)
I have the 3.66 Datens copied to all the relevant folders in NCS and EDIABAS and I am at a loss on how to proceed ...
Anyone have any idea?
Is the “na” in the above trace not acceptable?
Should I change this to nicht_aktiv or to anything else?
I am baffled ... what should be simple coding within reason is giving me sleepless nights!
Any Ideas? Thanks in advance ...